|
Specification |
|
PSU |
6-200 |
12.5-120 |
20-76 |
40-38 |
60-25 |
100-15 |
150-10 |
300-5 |
400-3.8 |
600-2.6 |
|
Output ratings |
|
Rated outputvoltage (*1) (V) |
6 |
12.5 |
20 |
40 |
60 |
100 |
150 |
300 |
400 |
600 |
|
Rated outputcurrent (*2) (A) |
200 |
120 |
76 |
38 |
25 |
15 |
10 |
5 |
3.8 |
2.6 |
|
Rated outputpower (W) |
1200 |
1500 |
1520 |
1520 |
1500 |
1500 |
1500 |
1500 |
1520 |
1560 |
|
Ripple and noise(*5) |
|
CVp-p( 10 ~20MHz) p-p (*6) (mV) |
60 |
60 |
60 |
60 |
60 |
80 |
100 |
150 |
200 |
300 |
|
CVrms(5Hz ~1MHz) r.m.s. (*7) (mV) |
8 |
8 |
8 |
8 |
8 |
8 |
10 |
25 |
40 |
60 |
|
CCrms(5Hz ~1MHz) r.m.s.(*12) (mA) |
400 |
240 |
152 |
95 |
75 |
45 |
35 |
25 |
17 |
12 |
|
Load regulation |
|
Voltage(*4)(mV) |
2.6 |
3.25 |
4 |
6 |
8 |
12 |
17 |
32 |
42 |
62 |
|
Current(*11)(mA) |
45 |
29 |
20.2 |
12.6 |
10 |
8 |
7 |
6 |
5.76 |
5.52 |
|
Line regulation |
|
Voltage(*3)(mV) |
2.6 |
3.25 |
4 |
6 |
8 |
12 |
17 |
32 |
42 |
62 |
|
Current(*3)(mA) |
22 |
14 |
9.6 |
5.8 |
4.5 |
3.5 |
3 |
2.5 |
2.38 |
2.26 |
|
Analog Programming and Monitoring |
|
Externalvoltage control output voltage |
Accuracy and linearity: ±0.5% of rated output voltage. |
|
Externalvoltage control output current |
Accuracy and linearity: ±1% of rated output current. |
|
Externalresistor control output voltage |
Accuracy and linearity: ±1% of rated output voltage. |
|
Externalresistor control output current |
Accuracy and linearity: ±1.5% of rated output current. |
|
Output voltagemonitor |
Accuracy: ±1% |
|
Output currentmonitor |
Accuracy: ±1% |
|
Shutdowncontrol |
Turns the output off with a LOW (0V to 0.5V) or short-circuit. |
|
Output on/off control |
Possible logic selections: |
|
Turn the output on using aLOW (0V to 0.5V) or short-circuit, turn the output off using a HIGH (4.5V to5V) or open-circuit. |
|
Turn the output on using aHIGH (4.5V to 5V) or open-circuit, turn the output off using a LOW (0V to |
|
Alarm clearcontrol |
Clear alarms with a LOW (0V to 0.5V) or short-circuit. |
|
CV/CC/ALM/PWRON/OUT ON indicator |
Photocoupler open collector output;Maximum voltage 30V, maximum sink current 8mA. |
|
Trigger out |
Maximum low level output = 0.8V; minimumhigh level output = 2V; Maximum source current = 8mA. |
|
Trigger in |
Maximum low level input voltage = 0.8V;minimum high level input votage = 2V, Maximum sink current = 8mA. |
|
Front Panel |
|
Display, 4digits,
Voltage accuracy (0.1%+mV) |
12 |
25 |
40 |
80 |
120 |
200 |
300 |
600 |
800 |
1200 |
|
Current accuracy (0.2%+mA) |
600 |
360 |
228 |
114 |
75 |
45 |
30 |
15 |
11.4 |
7.8 |
|
Indications |
GREEN LEDs: CV, CC, V, A, VSR, ISR, DLY, RMT, LAN, M1, M2, M3,RUN,OutputON |
|
|
RED LEDs: ALM, ERR |
|
Buttons |
Lock/Local(Unlock), PROT(ALM_CLR),Function(M1), Test(M2), Set(M3), Shift, Output |
|
Knobs |
Voltage, Current |
|
USB port |
Type A USB connector |
|
Transient response time (*10) |
|
Transientresponse time (ms) |
1.5 |
1 |
1 |
1 |
1 |
1 |
2 |
2 |
2 |
2 |
|
Output response time |
|
Rise time (*8) |
|
Rated load(ms) |
80 |
80 |
80 |
80 |
80 |
150 |
150 |
150 |
200 |
250 |
|
No load (ms) |
80 |
80 |
80 |
80 |
80 |
150 |
150 |
150 |
200 |
250 |
|
Fall time(*9) |
|
Rated load (ms) |
10 |
50 |
50 |
80 |
80 |
150 |
150 |
150 |
200 |
250 |
|
No load (ms) |
500 |
700 |
800 |
1000 |
1100 |
1500 |
2000 |
2500 |
3000 |
4000 |
|
Programming and Measurements (RS-232/485, USB, LAN, GPIB) |
|
Programming accuracy |
|
Outputvoltage (0.05%+mV) |
3 |
6.25 |
10 |
20 |
30 |
50 |
75 |
150 |
200 |
300 |
|
Output current(0.2%+mA) |
200 |
120 |
76 |
38 |
25 |
15 |
10 |
5 |
3.8 |
2.6 |
|
Programming resolution |
|
Output voltage(mV) |
0.2 |
0.4 |
0.7 |
1.3 |
2 |
3.4 |
5.2 |
10.2 |
13.6 |
20.4 |
|
Output current(mA) |
6 |
4 |
2.5 |
1.2 |
0.8 |
0.5 |
0.34 |
0.19 |
0.13 |
0.09 |
|
Measurement accuracy |
|
Output voltage(0.1%+mV) |
6 |
12.5 |
20 |
40 |
60 |
100 |
150 |
300 |
400 |
600 |
|
Output current(0.2%+mA) |
400 |
240 |
152 |
76 |
50 |
30 |
20 |
10 |
7.6 |
5.2 |
|
Measurement resolution |
|
Output voltage(mV) |
0.2 |
0.4 |
0.7 |
1.3 |
2 |
3.4 |
5.2 |
10.2 |
13.6 |
20.4 |
|
Output current(mA) |
6 |
4 |
2.5 |
1.2 |
0.8 |
0.5 |
0.34 |
0.19 |
0.13 |
0.09 |
|
Temperature coefficience |
|
Voltage (ppm/℃) |
100ppm/℃ after a 30 minute warm-up |
|
Current (ppm/℃) |
100ppm/℃ after a 30 minute warm-up |
|
Remote sense compensation voltage(single wire) |
|
voltage |
1 |
1 |
1 |
2 |
3 |
5 |
5 |
5 |
5 |
5 |
|
Protection Function |
|
Over voltage protection(OVP) |
|
Setting range(V) |
0.6 - 6.6 |
1.25 - 13.75 |
02월 22일 |
4 - 44 |
5 - 66 |
5 - 110 |
5 - 165 |
5 - 330 |
5 - 440 |
5 - 660 |
|
Settingaccuracy (mV) |
60 |
125 |
200 |
400 |
600 |
1000 |
1500 |
3000 |
4000 |
6000 |
|
Over current protection(OCP) |
|
Setting range(A) |
5 - 220 |
5 - 132 |
5 - 83.6 |
3.8 - 41.8 |
2.5 - 27.5 |
1.5 - 16.5 |
1 - 11 |
0.5 - 5.5 |
0.38 - 4.18 |
0.26 - 2.86 |
|
Settingaccuracy (mA) |
4000 |
2400 |
1520 |
760 |
500 |
300 |
200 |
100 |
76 |
52 |
|
Under voltage limit(UVL) |
|
Setting range |
0 - 6.3 |
0 - 13.12 |
0 - 21 |
0 - 42 |
0 - 63 |
0 - 105 |
0 - 157.5 |
0 - 315 |
0 - 420 |
0 - 630 |
|
Overtemperature protection(OHP) |
Turn the output off. |
|
Incorrectsensing connection protection (SENSE) |
Turn the output off. |
|
Low AC inputprotection (AC-FAIL) |
Turn the output off. |
|
Shutdown (SD) |
Turn the output off. |
|
Power limit(POWER LIMIT) |
Over power limit. |
|
Approx. 105% of rated output power |
|
Interface Capabilities |
|
USB |
TypeA: Host, TypeB: Slave, Speed:1.1/2.0, USB Class: CDC(Communications Device Class) |
|
LAN |
MAC Address, DNS IP Address, UserPassword, Gateway IP Address, Instrument IP Address, Subnet Mask |
|
RS-232 /RS-485 |
Complies with the EIA232D / EIA485Specifications |
|
GPIB (FactoryOption) |
SCPI - 1993, IEEE 488.2 compliantinterface |
|
Isolated Analog Control Interface (Factory Option) |
|
VoltageControl |
Using 0-5V or 0-10V signals forprogramming and measurement |
|
CurrentControl |
Using 4-20mA current signals forprogramming and measurement |
|
Environmental Conditions |
|
Operatingtemperature |
0˚C to 50˚C |
|
Storagetemperature |
-25˚C to 70˚C |
|
Operatinghumidity |
20% to 85% RH; No condensation |
|
Storagehumidity |
90% RH or less; No condensation |
|
Altitude |
Maximum2000m |
|
Input Characteristics |
|
Nominal inputrating |
100Vac to 240Vac, 50Hz to 60Hz, single phase |
|
Input voltagerange |
85Vac ~ 265Vac |
|
Inputfrequency range |
47Hz ~ 63Hz |
|
Maximum inputcurrent (A) |
21(100Vac) / 11(200Vac) |
|
Inrush current |
Less than50A. |
|
Maximum inputpower (VA) |
2000 |
|
Power factor |
0.99 / 0.98 |
|
Efficiency(*13) (100Vac / 200Vac) (%) |
77 / 79 |
82 / 85 |
83 / 86 |
84 / 87 |
84 / 87 |
84 / 87 |
84 / 87 |
84 / 87 |
84 / 87 |
84 / 87 |
|
Hold-up time |
20ms or greater |
|
General |
|
Weight |
Less than 8.7kg (main unit only) |
|
Dimensions |
423(W)×43.6(H)×447.2(D) mm |
|
Cooling |
Forced air cooling by internal fan. |
|
EMC |
Complies with the European EMC directive89/336/EEC for Class A test and measurement products. |
|
Safety |
Complies with the European Low VoltageDirective 73/23/EEC and carries the CE-marking. |
|
Withstand voltage |
AC to Chassis : 1500Vac / 1min |
|
AC to Output terminal :3000Vac / 1min |
|
Vout?150V |
|
Output terminal to Chassis: 1000Vdc / 1min |
|
Vout150V |
|
Output terminal to Chassis: 1500Vdc / 1min |
|
Insulationresistances |
Chassis and output terminal; chassis andAC input; AC input and output terminal: 100MΩ or more (DC 1000V) |
계측기
